# V4 Modbo modchip installation diagram \- William Quade Canonical: Language: `en-US` ![V4 Modbo installation diagram \(no gap\)](https://quade.co/wp-content/uploads/2018/11/V4-No-Gap.jpg) One of the revisions of the fat PlayStation 2 was the V4\. They were found in many of the earliest SCPH\-3000x systems, as well as the SCPH\-3500x systems\. Matching console model numbers and board numbers are listed below\. You can find the model number on the sticker on the bottom of the console, and the board number is printed on the PS2 main board if you take apart your console\. Note that there can be multiple board numbers within a specific model number\. - NTSC\-J \(Japan\): - SCPH\-30000 \(GH\-010\) - SCPH\-35000 \(GH\-010\) - NTSC\-U/C \(United States\) - SCPH\-30001 \(GH\-010\) - SCPH\-35001 \(GH\-010\) - PAL - SCPH\-30002 \(GH\-010\) - SCPH\-30003 \(GH\-010\) - SCPH\-30004 \(GH\-010\) - SCPH\-35002 \(GH\-010\) - SCPH\-35003 \(GH\-010\) - SCPH\-35004 \(GH\-010\) - SCPH\-35005 \(GH\-010\) Note that there are multiple versions of the Modbo modchips available, but the installation diagrams are all the same\. Some example versions are Modbo 3\.0, Modbo 4\.0, Modbo 5\.0, and Modbo 750\. For more information about [Modbo modchips click here](https://quade.co/ps2-modchip-guide/modbo/) , for more information about [PS2 modchips in general click here](https://quade.co/ps2-modchip-guide/) \. # V4 Modbo installation diagram [![Modbo modchip pinout](https://quade.co/wp-content/uploads/2018/11/Modbo-4.0-Layout.jpg)](https://quade.co/wp-content/uploads/2018/11/Modbo-4.0-Layout.jpg) Some V4 consoles have a gap in the middle of the pins of the BIOS chip \(near pins Q, T, U, V, R, O, P, N, and M\)\. For those systems use this diagram: [![V4 Modbo installation diagram \(gap\)](https://quade.co/wp-content/uploads/2018/11/V4-Gap.jpg)](https://quade.co/wp-content/uploads/2018/11/V4-Gap.jpg) Some V4 consoles don’t have a gap in the middle of the pins of the BIOS chip \(near pins Q, T, U, V, R, P, O, N, and M\)\. For those systems use this diagram: [![V4 Modbo installation diagram \(no gap\)](https://quade.co/wp-content/uploads/2018/11/V4-No-Gap.jpg)](https://quade.co/wp-content/uploads/2018/11/V4-No-Gap.jpg) # Installation tips Here are some tips I have for you when you are soldering your chip into a V4\. - Using 30 AWG solid core wire works well for most of the points\. - Use some thicker wire for the 5V and ground wires\. # Example installations This section has photos of some successful installations which you can use to get a better understanding of how everything is wired and positioned\. Leave a comment and I’ll add your installation to the list - William Quade \(me\) 51 Comments Most Voted Newest Oldest ![Greg](https://secure.gravatar.com/avatar/b89cb82f59164b92af0d8da92720a1de584f5d2988515b27e581068d1ca5af60?s=64&d=mm&r=g) Greg May 4, 2019 6:58 AM Hello, Here is my install on a Fat PS2 SCPH\-30001 \(GH\-010\) [https://imgur\.com/gallery/MQs0Rg1](https://imgur.com/gallery/MQs0Rg1) Used stranded 30 AWG because I dont like using kynar wire \(had to use it for 1 connection\)\. No glue on any of the wires but I feel like it came out ok\. Thanks for the well formatted website, very helpful\. 5 ![JayBee](https://secure.gravatar.com/avatar/14ebc588b0daeb3f05bcd71a67b62083145ed9ea7b17269b73dcda760a68c131?s=64&d=mm&r=g) JayBee December 3, 2019 8:44 AM Hello, I successfully installed the modbo v5\.0 on a SCPH\-30000 \(GH\-010\) too, thanks a lot for your help 😀 1 ![LAC](https://secure.gravatar.com/avatar/4def10ce465698c729be9cc59c828316d31b8926df6168c82e492b7cf467346a?s=64&d=mm&r=g) LAC April 16, 2019 11:18 AM Hello, you can add me \(LAC\) to the list\. It’s working, thank you\. 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) April 18, 2019 11:36 PM Reply to [LAC](#comment-2276) I’ve added you to the list\. 0 ![Obiwan Kenobi](https://secure.gravatar.com/avatar/d5ca6f247ce975dc1d24f686f0425a11260069f494513ee0d70220b38ecf024c?s=64&d=mm&r=g) Obiwan Kenobi March 22, 2020 4:32 PM Hi guys, Hope all is safe and sound\. I’m ready to attack this install \(on SCPH\-30001 US\) to ease my mind off from whatever happens in the world now with the novel COVID\-19\! Quick question: What’s with the ALT pics from the bottom on diagram instruction sheet? \(ALTernate? Are they neccessary?\) Thank you\! TangoRom 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) March 23, 2020 8:54 AM Reply to [Obiwan Kenobi](#comment-3155) You need to connect every point on the modchip to the console\. The ALT in the diagram is showing that there are multiple alternate locations that you can find some of those points\. 0 ![Charlie](https://secure.gravatar.com/avatar/64dfc8fe8963013ca1dc83c8dc2fa1d6a1b1a87ffefce172913f6ff67d380c8d?s=64&d=mm&r=g) Charlie April 18, 2020 10:28 AM Hi\! My son’s ps2 fat is a UK version, model SCPH\-30003 \(GH\-014\) which isn’t listed and I can’t seem to find any info online ? Any info would be greatly appreciated\. 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) April 18, 2020 10:31 AM Reply to [Charlie](#comment-3545) That’s probably a V4 or a V5\. You’d have to compare the diagrams to your actual board\. 0 ![Matt V](https://secure.gravatar.com/avatar/e2ef505da998b06502391ea213637810d6d630283b1f7bff6434cd22d6583816?s=64&d=mm&r=g) Matt V April 22, 2020 8:15 PM Whelp\.\. I really suck at this\. Someone want a fun try to un f\*\*ck it project? 0 ![Doc](https://secure.gravatar.com/avatar/f9dc94e70799d4d5d9e3263882c87c55d7727fd105321292c0f91fcd74777e0e?s=64&d=mm&r=g) Doc May 20, 2020 4:33 PM Hello, I have a SCPH\-30001 with serial starting U3, which I believe makes it a V4; I haven’t used it in years, instead I’ve used a slim PS2 with a Matrix I’ve had for over 10 years\. Is it indeed possible to mod this with a MODBO? If so, once your service opens up again, I may just sign up\. 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) May 20, 2020 8:47 PM Reply to [Doc](#comment-4106) Yeah, it’s possible to install a Modbo chip into a V4 board\. I’ll likely have the PS2 chip install eBay listing back in stock by Monday \(I have a few systems on hand or on the way that need to get done before selling more install services\)\. 0 ![Giorgio](https://secure.gravatar.com/avatar/d71e8b0f8e3513f7a0137649357644e2b9fc68d9ae07e7c0aea79ddde81b8e69?s=64&d=mm&r=g) Giorgio May 26, 2020 5:27 PM hi\! i’ve installed a modbo 5\.0 on a gh\-013 \(v4\)mainboard whitout the “H” pin \(ps2 pal\) it right? but it doesn’t work\! can someone help me please? With original cd is still working 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) May 26, 2020 5:28 PM Reply to [Giorgio](#comment-4185) Connect pin H\. 0 ![Giorgio](https://secure.gravatar.com/avatar/d71e8b0f8e3513f7a0137649357644e2b9fc68d9ae07e7c0aea79ddde81b8e69?s=64&d=mm&r=g) Giorgio May 27, 2020 5:33 AM Reply to [William Quade](#comment-4186) ok i’l do but why in the diagram is it only for ntsc consoles? 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) May 27, 2020 5:34 AM Reply to [Giorgio](#comment-4187) I don’t know since I didn’t make the diagram\. From my experience all pins need to be connected on all regions\. 0 ![Giorgio](https://secure.gravatar.com/avatar/d71e8b0f8e3513f7a0137649357644e2b9fc68d9ae07e7c0aea79ddde81b8e69?s=64&d=mm&r=g) Giorgio May 27, 2020 5:36 AM Reply to [William Quade](#comment-4188) Ok thank you 0 ![Ken Ballast](https://secure.gravatar.com/avatar/7cf33f0f27bd139ae5fd359ac9a86e2d9a723934d7968f153586b4f6d18e0dcb?s=64&d=mm&r=g) Ken Ballast June 20, 2020 5:34 AM Hi\. Is there an alternative solder point for “point Q”? I have the no gap version of v4 motherboard\. I messes up the litter copper square where Point Q must be soldered\. Hope you can help me\. 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) June 20, 2020 4:54 PM Reply to [Ken Ballast](#comment-4262) It should connect to one of the pins on the other side of the BIOS chip\. If you find point T on the chip with a multimeter it should be two pins above that\. 0 ![Gabrijel](https://secure.gravatar.com/avatar/a65909290be83b30852ec1cd5bb92b0b255c3a742d6d266c9150a23cde26dd0a?s=64&d=mm&r=g) Gabrijel July 1, 2020 8:58 AM Is it possible to install the modbo 4\.0 chip on the ps2 slim scph 90002, or should I look for another chip\. 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) July 1, 2020 9:24 AM Reply to [Gabrijel](#comment-4302) Yes it is\. 0 ![Mario](https://secure.gravatar.com/avatar/063c6f98d67c2280cb9f2ce1d792724c473c79ae792d6ab62e0ff5c92c1f8963?s=64&d=mm&r=g) Mario September 7, 2020 11:38 PM Hi, can you make a zoom in the point cx in your photo? Thaks\! 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) September 8, 2020 8:34 AM Reply to [Mario](#comment-4503) No, that part of my picture is too out of focus\. The point is very small but it should be very obvious which one it is if you find the spot on the board\. It’s right near the back of the HDD connector\. 0 ![Tom C](https://secure.gravatar.com/avatar/667c1425b26b033dbdf69dc56e674da87b111cd2338cfed8882aac4b33b9951d?s=64&d=mm&r=g) Tom C October 2, 2020 11:09 PM I just finished my install on the V4 board\. Currently however when I boot the PS2 on the TV screen it just shows the Matrix logo and doesn’t go any further\. I do hear the CD drive make a couple of very quick chirps like it’s trying to do something\. I tried to hold down the triangle and Circle to get into the menu, but nada, still sits on the logo screen\. Any ideas? 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) October 3, 2020 8:19 AM Reply to [Tom C](#comment-4559) Sounds like an issue with one of the BIOS pins \(M, N, O, P, Q, T, U, V, R, W\) 0 ![Mike Black](https://secure.gravatar.com/avatar/85a070b2021ca10771b862583d17f301ee7f85be45fc094ab3138cbdfa80efde?s=64&d=mm&r=g) Mike Black October 21, 2020 4:40 PM Hello\. I just today installed my MODBO 5\.0 chip\. The problem I’m having is, when I boot up my PS2 \(SCPH\-35001\) There is a terrible distorted audio problem\. It sounds like someone shoved my speakers into a blender\. I tore it back down and inspected my solder points\. I didn’t have any bridged leads, however, I DID have a few unstable joints\. I re\-soldered those until I felt good about them\. Plugged my PS2 back up and still have the same issue\. Any help would be greatly appreciated\. Thank You 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) October 21, 2020 9:00 PM Reply to [Mike Black](#comment-4575) It’s hard to say what exactly went wrong\. Check for any blown fuses on the PS2 board\. 0 ![RudeRGB](https://secure.gravatar.com/avatar/aaa2585e7dc2cfa83640238e0110a9df0d8adc0d60a7770e169478a24ad78894?s=64&d=mm&r=g) RudeRGB April 10, 2021 5:21 AM Reply to [Mike Black](#comment-4575) reflow resistor block 470 near sound DSP \(if you put modbo on this\) 0 ![Sergio](https://secure.gravatar.com/avatar/da65d2637181d3e46d148b7ccee85046552bcac5571b917a84c443b56ee4184a?s=64&d=mm&r=g) Sergio January 24, 2021 5:46 PM Hello, i’m about to istall the modbo 5\.0 chip on my PS2 Fat SCPH 30004 v4\. All in the connections diagram is clear beside the ABHI pins on the motherboard\. There are two different pictures of those pins in two different location of the board\. I have to use either one or the other at my choice? Thanks for the answer, and sorry for a maybe silly question\. Sergio 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) January 24, 2021 5:47 PM Reply to [Sergio](#comment-4749) They are equivalent/alternative points\. You can use one or the other or the combination of the two\. 0 ![Sergio](https://secure.gravatar.com/avatar/da65d2637181d3e46d148b7ccee85046552bcac5571b917a84c443b56ee4184a?s=64&d=mm&r=g) Sergio January 25, 2021 3:39 AM Reply to [William Quade](#comment-4750) Thanks William\. I thought so, but before jamming the whole stuff i wanted to be sure\. 0 ![New\_Meddle](https://secure.gravatar.com/avatar/ffe9ed42389ef93b5e7205de31b0e6107d65b39592e238fe69f620dc970667d1?s=64&d=mm&r=g) [New\_Meddle](https://www.facebook.com/NewMeddleRepairs/) February 7, 2021 4:31 PM Successful install by me New\_Meddle on a V4 \(GH\-013\) SCPH\-30001 motherboard\! Thank you for the guide William\. 0 ![New\_Meddle](https://secure.gravatar.com/avatar/ffe9ed42389ef93b5e7205de31b0e6107d65b39592e238fe69f620dc970667d1?s=64&d=mm&r=g) [New\_Meddle](https://www.facebook.com/NewMeddleRepairs/) February 7, 2021 4:32 PM Here’s the link, sorry I didn’t include it in the other post\. [https://imgur\.com/a/MOfeUle](https://imgur.com/a/MOfeUle) 0 ![Ezequiel](https://secure.gravatar.com/avatar/ebda0064022237e7b0c4ecf64678b676c27164b9f288543d8cc614de78eaaa6c?s=64&d=mm&r=g) Ezequiel April 9, 2021 11:24 PM Reply to [New\_Meddle](#comment-4777) New\_Meddle Hello friend, I see your image that you uploaded, I have the same GH\-013 plate only that the said image does not appear, the CX point could you help me in the diagram that point does not appear is different\. 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) April 11, 2021 9:28 AM Reply to [Ezequiel](#comment-4910) Sometimes there will be component on the two pads to the right of where the CX point is in the diagram\. It’s still the same spot, but just the surrounding parts look a little different\. 0 ![Aldair](https://secure.gravatar.com/avatar/80e89fb096db92261302a129bb02b2543e27015aa2cd73d93f2af066a89a7ddc?s=64&d=mm&r=g) Aldair July 27, 2021 9:27 PM Reply to [New\_Meddle](#comment-4777) I ended up ruining the copper at the “U” point, would there be another alternative place to solder this point? 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) July 28, 2021 11:39 AM Reply to [Aldair](#comment-5113) It connects to the pins on the opposite side of the chip that has P, O, N, M points are on\. The pins and pads have the same spacing/ordering\. 0 ![Aldair](https://secure.gravatar.com/avatar/80e89fb096db92261302a129bb02b2543e27015aa2cd73d93f2af066a89a7ddc?s=64&d=mm&r=g) Aldair July 28, 2021 1:03 PM Reply to [William Quade](#comment-5116) in this case solder with the same spacing on the other side of the chip near the “W” point? 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) July 28, 2021 1:04 PM Reply to [Aldair](#comment-5118) Yes, but count down the spacing from the top of the chip\. 0 ![Panos](https://secure.gravatar.com/avatar/d4364d0f0490fb73a4c17411cfff0692c78f0620067e29b6272c3bf8383f3184?s=64&d=mm&r=g) Panos February 10, 2021 2:48 PM Hi my board product number is gh014 and my ps2 fat is scph\-30004\(its not listed probably v4\)i made it as ver 4\. all pins from the diagram looks the same except “cx” pin witch I am not sure and i think that’s the problem \.\.its my second ps2 with modbo 5 and it doesn’t read the cd i burned but with the original games its ok\.\.it appears disk read error with burned dvds 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) February 10, 2021 8:18 PM Reply to [Panos](#comment-4790) What does your board look like near where the CX point is? It’s not going to work without a correct CX point soldered\. 0 ![CabriDIY](https://secure.gravatar.com/avatar/3e38b931cde6259f3a9b463958f15077f0fd2052d73b8341ac90f4d86c242d32?s=64&d=mm&r=g) [CabriDIY](http://cabridiy.fr) February 13, 2021 9:28 AM Hello, thanks for all your work 🙂 I install an Modbo 5\.0 on SCPH\-35004 GH\-012 and I have a problem\. The Modbo working well but I can’t open the tray … When I manually put a disc on it it’s working good but when I push the eject button the tray won’t open\. And when I manually open the tray and I push the eject button the tray closes\. Do you have an idea of my problem ? 🙂 Thanks by advance 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) February 14, 2021 7:56 AM Reply to [CabriDIY](#comment-4799) Did you accidentally knock if off of the rail or not connect all of the cables back to the board? 2 ![CabriDIY](https://secure.gravatar.com/avatar/3e38b931cde6259f3a9b463958f15077f0fd2052d73b8341ac90f4d86c242d32?s=64&d=mm&r=g) [CabriDIY](http://cabridiy.fr) February 15, 2021 1:19 AM Reply to [William Quade](#comment-4800) Thanks for your speed reply\. I reflow the driver and now the console working perfectly 🙂 Thanks for all your work 😉 0 ![Sergio](https://secure.gravatar.com/avatar/da65d2637181d3e46d148b7ccee85046552bcac5571b917a84c443b56ee4184a?s=64&d=mm&r=g) Sergio February 26, 2021 10:17 AM My board is coded GH\-012, looks fairly similar to the GH\-10, beside the chips on the back of the board\. I still use the GH\-010 instructions? 0 ![Sergio](https://secure.gravatar.com/avatar/da65d2637181d3e46d148b7ccee85046552bcac5571b917a84c443b56ee4184a?s=64&d=mm&r=g) Sergio February 27, 2021 5:23 PM I have a big trouble occoourred during the mod\. One of the pitch under one pin of a chip… slided away\. Still thereby, bit not in his position\. Is it possibile to put it back where it was, or i just wanted the motherboard? 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) March 1, 2021 1:42 PM Reply to [Sergio](#comment-4830) You lifted a solder pad? You’ll probably need to find an alternate point to solder to if that happened, assuming the system still works\. 0 ![Sergio](https://secure.gravatar.com/avatar/da65d2637181d3e46d148b7ccee85046552bcac5571b917a84c443b56ee4184a?s=64&d=mm&r=g) Sergio March 1, 2021 1:44 PM Reply to [William Quade](#comment-4832) got the service manual\. Found the alternative place\. Thanks\. 0 ![Sergio](https://secure.gravatar.com/avatar/da65d2637181d3e46d148b7ccee85046552bcac5571b917a84c443b56ee4184a?s=64&d=mm&r=g) Sergio March 11, 2021 4:44 AM Ok, after a long fight we did it\. I just have a silly, silly question\. Before reassembling the console: Being in Italy i suppose I have a European PS2\. This means i don’t have to connect the H pin, right? 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) March 11, 2021 6:04 AM Reply to [Sergio](#comment-4849) You’ll need to connect pin H\. It is required for the Chinese clone modchips that are sold today\. 0 ![ian swift](https://secure.gravatar.com/avatar/80aabab76d11f89392fb7f57f0ad5e5b4433a984c84d8d442be0ee978928b98a?s=64&d=mm&r=g) ian swift May 24, 2021 3:54 PM is 18awg ok for the 5v and ground connections? i stripped some from a power supply connection\. 0 [![William Quade](https://secure.gravatar.com/avatar/14ac9361c0296cbe4c2282fc8bdbd92bd0f1f946ca84939cc222c68e865637e5?s=64&d=mm&r=g)](https://quade.co/) Author [William Quade](https://quade.co/) May 24, 2021 3:54 PM Reply to [ian swift](#comment-5019) Yes 1